Although June passed, here is a post on last month's birthstone.
Showing posts with label pearls. Show all posts
Showing posts with label pearls. Show all posts
Wednesday, July 1, 2009
June Birthstone: Alexandrite or Pearl
Monday, October 20, 2008
Testing for Real Pearls
A lovely customer came to Handiwork today and wanted to have her pearls re-strung. The cutest part was that she did not know if they were genuine pearls. I taught her this simple pearl test everyone should know how to do.


Take two of the pearls and scratch them together. You should feel a slight resistance as the pearls nacre create friction against one another. Note the small feathery "scratches" left where the two pearls rubbed against one another.
Fake pearls will NOT scratch against one another. In fact, you will find they are slippery and have a plastic feel to them. Natural pearls may also have small blemishes, bumps, and color gradations.
Hopefully this pearl scratching trick will replace that funny habit people have developed -- using one's teeth to scratch the pearl's nacre!
Hopefully this pearl scratching trick will replace that funny habit people have developed -- using one's teeth to scratch the pearl's nacre!
Friday, October 3, 2008
Re-stringing Pearls
Most pearl necklaces will need to be re-strung every few years, depending upon wear and tear. The heavier the pearls (often of higher quality and larger) have a much more noticeable wearing effect on the string, resulting in frayed strands. The worst case scenario is when the pearl strand breaks. If your pearl necklace was strung properly with knots in between, you will not lose your pearls when the pearl strand breaks.
If you are up for learning to do this on your own, then your best luck may be at a craft store. Look for thin silk thread, small wire/beading needles, a pair of small sharp scissors (pointed tips), and super glue.




The next item is not necessary but it definitely makes knotting easier, faster, and tighter. You can find such knotting tools on Amazon or here.


Here is a small box of French wire (silver colored) that is often used to prevent the string from fraying after prolonged contact with the jump ring of the clasp.
After cutting your pearls or beads, place them onto a piece of cloth so they will not roll around. Take care to keep them in the correct order if they are different sizes or have a specific pattern. If your pearls need some cleaning, take a damp cloth and gently rub off any dirt.
Here are some guiding steps:
1. Measure your necklace or bracelet and multiply this length by four (4). For example, you will need 28" of silk thread for a standard 7" bracelet. Once you become more accustomed to stringing, you can be more conservative. In the beginning, however, the extra thread will be useful and allows room for knots.
2. Thread the silk through the eye of the beading needle.
3. Double the thread and knot the end.

4. String two (2) pearls onto the thread.

5. Cut a small piece of French wire (either gold or silver color) and thread this small piece onto the thread.

6. Thread the jump ring of the clasp onto the thread.
7. Loop the needle back into the nearest pearl, pull until the French wire becomes a small loop. No thread should be seen closest to the clasp.



8. Tie a knot as close as possible to first pearl.
9. Loop the needle through the second pearl and knot as close as possible. There should be a small piece of thread left with the very first knot. Do NOT cut this piece of thread yet.

10. Continue stringing all pearls onto the thread.

11. Use a beading tool like the one below to help tie knots as close as possible to the pearl.











12. STOP knotting when you have two (2) pearls left to finish.
13. Repeat steps 5 to 7, but this time you will need to carefully push the last two pearls together to avoid seeing any of the silk thread.

14. Tie a knot by hand.
15. Now you can close the knots by either (1) carefully super gluing or (2) burning the thread together. I usually super glue using the tip of an old needle or safety pin. Avoid excess super glue because it will make the knot large and unsightly.
If you are up for learning to do this on your own, then your best luck may be at a craft store. Look for thin silk thread, small wire/beading needles, a pair of small sharp scissors (pointed tips), and super glue.
The next item is not necessary but it definitely makes knotting easier, faster, and tighter. You can find such knotting tools on Amazon or here.
Here is a small box of French wire (silver colored) that is often used to prevent the string from fraying after prolonged contact with the jump ring of the clasp.
Here are some guiding steps:
1. Measure your necklace or bracelet and multiply this length by four (4). For example, you will need 28" of silk thread for a standard 7" bracelet. Once you become more accustomed to stringing, you can be more conservative. In the beginning, however, the extra thread will be useful and allows room for knots.
2. Thread the silk through the eye of the beading needle.
3. Double the thread and knot the end.
4. String two (2) pearls onto the thread.
5. Cut a small piece of French wire (either gold or silver color) and thread this small piece onto the thread.
6. Thread the jump ring of the clasp onto the thread.
7. Loop the needle back into the nearest pearl, pull until the French wire becomes a small loop. No thread should be seen closest to the clasp.
8. Tie a knot as close as possible to first pearl.
9. Loop the needle through the second pearl and knot as close as possible. There should be a small piece of thread left with the very first knot. Do NOT cut this piece of thread yet.
10. Continue stringing all pearls onto the thread.
11. Use a beading tool like the one below to help tie knots as close as possible to the pearl.
12. STOP knotting when you have two (2) pearls left to finish.
13. Repeat steps 5 to 7, but this time you will need to carefully push the last two pearls together to avoid seeing any of the silk thread.
14. Tie a knot by hand.
15. Now you can close the knots by either (1) carefully super gluing or (2) burning the thread together. I usually super glue using the tip of an old needle or safety pin. Avoid excess super glue because it will make the knot large and unsightly.
Subscribe to:
Posts (Atom)
